Quick Start Guide: Tilting Cold Shoe Mount for Insta360 Luna Ultra Screen

What You’re Installing

This mount adds a standard cold shoe connection and 195 degrees of adjustable tilt to your removable Insta360 Luna Ultra screen.

The mount can slide forward or backward inside the cold shoe before tightening, allowing you to find the best screen position for your rig.

In the Box

• Tilting Cold Shoe Mount for Insta360 Luna and Luna Ultra Screen

Insta360 screen, camera, rig, handles, and other accessories are sold separately.

Before You Begin

• Power off the removable screen before installing it.
• Make sure the screen and the mount’s screen connection are clean.
• Confirm that your handle, cage, bracket, or camera rig has an open standard cold shoe.
• Remove anything that may prevent the screen from connecting fully to the mount.

Setup Steps

1. Remove and Power Off the Screen

Remove the Luna Ultra screen from the camera and power it off before installation.

2. Align the Screen With the Mount

Align the rear mounting connection on the Luna Ultra screen with the screen connection on the tilting mount.

Make sure the screen is facing the correct direction and is straight before attaching it.

3. Attach the Screen

Place the screen onto the mount until the mounting connection is fully seated.

Gently check that the screen is secure. Do not twist the screen or force the connection at an angle.

4. Loosen the Cold Shoe Locking Knob

Turn the locking knob counterclockwise just enough for the cold shoe foot to slide freely.

Do not completely remove the locking knob.

5. Slide the Mount Into the Cold Shoe

Slide the cold shoe foot completely into the cold shoe on your handle, cage, bracket, or camera rig.

Keep the locking knob slightly loose so the mount can still slide forward and backward.

6. Find the Best Position

Slide the mount forward or backward inside the cold shoe.

Position the screen where it is easy to see and clear of handles, cables, controls, and other accessories.

7. Lock the Mount in Place

Hold the mount in the selected position and turn the locking knob clockwise until the mount is secure.

Hand-tighten only. Do not use pliers or over-tighten the locking knob.

Confirm that the mount cannot slide or rotate before moving the rig.

8. Set the Viewing Angle

Hold the rig steady with one hand. Use the other hand to push or pull from the back of the mount until the screen reaches the desired angle.

The hinge provides up to 195 degrees of adjustment. Do not force the hinge past the end of its normal movement.

9. Adjust the Hinge Tension

If the hinge moves too easily or feels too firm, use a 2.5mm hex key to adjust the hinge screw in small increments.

• Turn clockwise for a firmer hold.
• Turn counterclockwise for easier movement.
• Test the hinge after each small adjustment.

Do not fully remove the hinge screw.

10. Power On and Check the Mount

Power on the Luna Ultra screen.

Confirm that the screen is connected securely, the cold shoe knob is tight, and the hinge holds the selected viewing angle.

Removing the Screen

1. Power off the Luna Ultra screen.
2. Loosen the cold shoe locking knob and remove the complete mount from the rig.
3. Hold the screen and mount by their supported areas.
4. Carefully disconnect the screen using its normal removal direction.
5. Do not pull on the display, twist the connection, or use the hinge as a removal lever.

Quick Troubleshooting

• Screen will not connect: Check its orientation and make sure the mounting surfaces are clean. Do not force the connection.
• Screen feels loose: Remove it and reconnect it, making sure the mounting connection is fully seated.
• Mount slides in the cold shoe: Make sure the cold shoe foot is fully inserted, then tighten the locking knob.
• Mount rotates: Confirm that the locking knob is tightened and the cold shoe is compatible with the mount.
• Screen angle drifts: Tighten the hinge screw slightly with a 2.5mm hex key.
• Hinge is difficult to move: Loosen the hinge screw slightly and move the screen using the back of the mount.
• Mount will not fold flat: Check for cables or accessories blocking its movement. Do not force it.

Need Help?

Any issues or questions, please start a chat on the store and we’ll help you get set up.